Emotiva

XPA-3 Gen3

Name: XPA-3 Gen3
Brand: Emotiva
SKU: EMOTIVA-XPA-3-GEN3

3 Channel Amplifier

الطراز AMP-XPA-CHAN-GEN3-3 · السلسلة XPA

The new XPA-3 is a three-channel audiophile quality power amplifier, and is perfect for powering the three important front channels of a 5.1 channel, 7.1 channel, or Dolby Atmos / DTS:X home theater system.

اقرأ المزيد

لمحة سريعة

جميع المواصفات

Gain: 29 dB
Maximum Power Consumption: 1,400 watts.

السعر عند الطلبتحقّق من التوفر

اطلب السعر

المزايا5
ملفات للتنزيل1
أفلام1

نظرة عامة

Before you blame your speakers, make sure your amp is not the one waving the white flag.

The XPA-3 Gen3 is a 3 channel audiophile home theater power amplifier built on our XPA Gen3 modular platform, made to bring clarity, impact, and control to the three most important speakers in your room: left, center, and right. It is also built to order. You heard that right – a modular amplifier built around the configuration you choose, with room to expand or reconfigure later as your system grows.

Connect it to an AV processor, preamp, or an AV receiver with preamp outputs (RCA jacks usually labeled “PRE OUT”), and you can upgrade your front stage without replacing your whole system. Its Class A/B output stage and regulated switch-mode power supply help it stay clean, steady, and composed when the soundtrack hits hard. Modules are installed by Emotiva, free with the purchase of new modules, or an authorized service center, and each amplifier includes its own birth certificate as a small reminder that it was built to order. It is designed, assembled, and tested in the USA.

Common uses:

•Power the front three channels of a 5.1 or 7.1 system with more clarity and control

•Upgrade an AVR’s front stage for cleaner dialogue, stronger dynamics, and a more believable soundstage

• Start with LCR now, then expand later as you build toward Dolby Atmos or DTS:X

Want a second set of eyes on your system plan? Contact us. Real humans, real answers, straight from the folks behind the gear.

المزايا

Modular Design That Grows With Your System
The XPA-3 Gen3 is not locked into a fixed long-term layout. It is part of our XPA Gen3 modular power amplifier platform, so you can start with three channels now and expand or reconfigure later as your system changes.
Three High-Powered Channels for Your Front Stage
We built the XPA-3 Gen3 to power the three speakers that do most of the heavy lifting in home theater: left, center, and right. That makes it a natural fit for the front stage in a 5.1, 7.1, Dolby Atmos, or DTS:X system where clarity, dynamics, and dialogue matter most.
Class A/B Sound With Smarter Power Delivery
Each channel uses a fully discrete Class A/B amplifier module for smooth, detailed sound, while our high-efficiency switch-mode power supply and Optimized Class H topology help deliver serious headroom without the bulk of an oversized traditional design. In real terms, that means more control when the soundtrack gets demanding.
Easy to Integrate With the Gear You Already Own
The XPA-3 Gen3 connects to an AV processor, stereo preamp, or an AV receiver with preamp outputs. With balanced XLR and unbalanced RCA inputs on each channel, it is easy to add to an existing system without rebuilding your whole rack.
Built for Serious Systems and Long-Term Use
A heavy-duty chassis, intelligent fault protection, trigger support, and a 5-year warranty make this an amplifier built for the long haul. Because it is part of our broader XPA family, it is also built around long-term flexibility, not just a fixed one-box solution.

المواصفات

CIRCUIT TOPOLOGY

CIRCUIT TOPOLOGY: The XPA-3 Gen3 is a fully modular audio power amplifier with a high-efficiency switch mode power supply (SMPS), independent, fully discrete, dual differential, high current, short signal path Class A/B amplifier modules, Optimized Class H™ power supply topology, and microprocessor-controlled fault protection. The XPA-3 is powered by a high efficiency, audiophile grade, Switch Mode Power Supply (SMPS).

AUDIO SPECIFICATIONS

AUDIO SPECIFICATIONS: The XPA-3 Gen3 features three of our High-Powered Single Channel Modules. Audio Specifications (Three High-Powered Single Channel Modules):
Power Output: 300 watts RMS/channel; 20 Hz – 20 kHz; THD<0.1%; 8 Ohms; one channel driven 550 watts RMS/channel; 20 Hz – 20 kHz; THD<0.2%; 4 Ohms; one channel driven 300 watts RMS/channel; THD<0.1%; 8 Ohms; two channels driven 490 watts RMS/channel; THD<0.1%; 4 Ohms; two channels driven 275 watts RMS/channel; THD<0.1%; 8 Ohms; ALL THREE channels driven 450 watts RMS/channel; THD<0.1%; 4 Ohms; ALL THREE channels driven
Power Bandwidth (at rated power; 4 Ohm - 8 Ohm load): 20 Hz to 20 kHz (+ / – 0.1 dB)
Broad Band Frequency Response: 5 Hz to 80 kHz +0/-2 dB
THD + noise: < 0.005%; at 100 watts RMS; 1 kHz; 8 Ohms
Signal to Noise Ratio (8 Ohm load): > 117 dB; ref FTC rated power; unbalanced input (A-weighted) > 91 dB; ref 1 watt; unbalanced input (A-weighted)
Minimum Recommended Load Impedance (per channel): 4 Ohms (one 4 Ohm load or two paralleled 8 Ohm loads).
Damping Factor (8 Ohm load): > 500
Input Sensitivity (for rated power; 8 Ohm load): 1.71 V
Gain: 29 dB
Maximum Power Consumption: 1,400 watts.
Note: The values shown refer to the amount of power the amplifier would consume while playing test tones continuously, on all channels, at full power, into a load bank. Therefore, they are not at all characteristic of what you would expect when playing music or the soundtrack from a movie. Normal audio signals are dynamic, so the amount of power they require from second to second varies widely, and the average is far lower than this. With normal content, even playing very loudly, one of our amplifiers will consume far less power than indicated in the chart, so these values should not be considered a circuit requirement for normal operation.
Input Impedance: 33 kOhms (balanced) 23.5 kOhms (unbalanced)

INPUT & OUTPUT CONNECTIONS

Input Connections (High-Powered Single Channel Modules): Unbalanced (RCA); balanced (XLR); one each per channel, independently selectable.
Input Connections (Stereo Modules): 2 Unbalanced (RCA); 2 balanced (XLR); two per channel, independently selectable.
Speaker Output Connections: Audiophile grade, gold plated, 5-way binding posts.

TRIGGER & POWER REQUIREMENTS

Trigger Input: 5 – 12 V (AC or DC); <10 mA input current required.
Trigger Output: 12 VDC; can drive any load up to 120 mA.
Power Requirements: Between 100 VAC and 250 VAC @ 50 / 60 Hz (automatically detected).

CONTROLS & INDICATORS

Standby: push button (halo ring changes color to indicate Standby or On).
Status LEDs: one per channel; blue Status LEDs change to red to indicate a fault condition
AC Power switch: rocker switch (switches AC main power)
Status LEDs switch: disables front panel Status LEDs and dims Standby button halo.
Input selector switches (one per channel): metal toggle switches; select between balanced and unbalanced inputs.
Circuit Breaker: press button to reset circuit breaker.

PROTECTION & MECHANICAL

Protection: The XPA Gen3 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions.
Dimensions: 17” wide x 8” high x 19” deep (unboxed; including feet) 17” wide x 7” high x 19” deep (unboxed; without feet) 24-1/2” wide x 12” high x 24-3/4” deep (boxed)
Weight: 39 lbs (unboxed) 44 lbs (boxed)