Emotiva

XPA-2 Gen3

Name: XPA-2 Gen3
Brand: Emotiva
SKU: EMOTIVA-XPA-2-GEN3

2 Channel Amplifier

Model AMP-XPA-CHAN-GEN3-2 · Series XPA

The XPA-2 is a two-channel audiophile quality power amplifier, and is perfect for powering superb quality stereos and sound systems. Shop online today!

At a glance

All specifications

Gain: 29 dB
Maximum Power Consumption: 1,000 watts.

Price on requestCheck availability

Request a price

Features5
Downloads1
Films1

Overview

Great stereo is not about volume, it’s about control.

The XPA-2 Gen3 is a two-channel power amplifier that connects to a stereo preamp, AV processor, or an AV receiver with PRE OUT connections (RCA or XLR), then delivers high-current power to the two speakers you assign it to.

It’s right at home in a serious stereo or 2.1 music system (with a powered subwoofer), and it’s also a killer upgrade for the front left and right channels in a home theater, where the biggest dynamics live. The XPA-2 ships with two High-Powered Single-Channel Class A/B modules installed and delivers 300 W/ch into 8 ohms or 490 W/ch into 4 ohms with both channels driven. Each channel supports balanced XLR or unbalanced RCA, selectable per channel.

Built on our XPA Gen3 modular platform, the chassis also leaves five module slots available for future expansion (modules must be installed by Emotiva or an authorized Emotiva service representative).

Configuration: 2 x High-Powered Single-Channel Modules (five module slots remain available for future expansion)

Power output:

300 watts/channel RMS into 8 Ohms; two channels driven

490 watts/channel RMS into 4 Ohms; two channels driven

Features

Two Channel Perfection
The XPA-2 Gen3 is built for the two channels that matter most in a stereo system: your main left and right speakers. It’s also a strong upgrade for the front L/R channels in a home theater, where clarity and dynamics can make or break the experience.
Modular Design
The XPA-2 is built on our XPA Gen3 modular platform and ships with two High-Powered Single-Channel modules installed. The chassis also leaves five module slots available for future expansion as your system changes (modules must be installed by Emotiva or an authorized Emotiva service representative).
Class A/B Power
Each channel uses a fully discrete Class A/B amplifier module with a short signal path and high current capability. Backed by a high-efficiency, regulated SMPS and Optimized Class H operation, it delivers clean detail and strong dynamics without sounding strained when the music gets demanding.
Easy Integration
Connect the XPA-2 to a stereo preamp, AV processor, or an AVR with PRE OUT connections, then choose balanced XLR or unbalanced RCA on each channel using the rear-panel input selector switches. Add trigger input and output, and it slots cleanly into both two-channel and home theater racks.
Protection
Microprocessor-controlled protection is designed to stay transparent during normal listening, yet guard against common fault conditions like overheating and shorted speaker connections. A resettable rear-panel circuit breaker helps protect against AC line issues, and the XPA-2 Gen3 is backed by our five-year warranty.

Specifications

CIRCUIT TOPOLOGY

CIRCUIT TOPOLOGY: The XPA-2 Gen3 is a fully modular audio power amplifier with a high-efficiency switch mode power supply (SMPS), independent, fully discrete, dual differential, high current, short signal path Class A/B amplifier modules, Optimized Class H™ power supply topology, and microprocessor-controlled fault protection. The XPA-2 is powered by a high efficiency, audiophile grade, Switch Mode Power Supply (SMPS).

AUDIO SPECIFICATIONS

AUDIO SPECIFICATIONS: The XPA-2 Gen3 features two of our High-Powered Single Channel Modules. Audio Specifications (Two High-Powered Single Channel Modules):
Power Output: 300 watts RMS/channel; 20 Hz – 20 kHz; THD<0.1%; 8 Ohms; one channel driven 550 watts RMS/channel; 20 Hz – 20 kHz; THD<0.2%; 4 Ohms; one channel driven 300 watts RMS/channel; THD<0.1%; 8 Ohms; two channels driven 490 watts RMS/channel; THD<0.1%; 4 Ohms; two channels driven
Power Bandwidth (at rated power; 4 Ohm - 8 Ohm load): 20 Hz to 20 kHz (+ / – 0.1 dB)
Broad Band Frequency Response: 5 Hz to 80 kHz +0/-2 dB
THD + noise: < 0.005%; at 100 watts RMS; 1 kHz; 8 Ohms
Signal to Noise Ratio (8 Ohm load): > 117 dB; ref FTC rated power; unbalanced input (A-weighted) > 91 dB; ref 1 watt; unbalanced input (A-weighted)
Minimum Recommended Load Impedance (per channel): 4 Ohms (one 4 Ohm load or two paralleled 8 Ohm loads)
Damping Factor (8 Ohm load): > 500
Input Sensitivity (for rated power; 8 Ohm load): 1.71 V
Gain: 29 dB
Maximum Power Consumption: 1,000 watts.
Note: The values shown refer to the amount of power the amplifier would consume while playing test tones continuously, on all channels, at full power, into a load bank. Therefore, they are not characteristic of what you would expect when playing music or the soundtrack from a movie. Normal audio signals are dynamic, so the amount of power they require from second to second varies widely, and the average is far lower than this. With normal content, even playing very loudly, one of our amplifiers will consume far less power than indicated in the chart, so these values should not be considered a circuit requirement for normal operation.
Input Impedance: 33 kOhms (balanced) 23.5 kOhms (unbalanced)

INPUT & OUTPUT CONNECTIONS

Input Connections (High-Powered Single Channel Modules): Unbalanced (RCA); balanced (XLR); one each per channel, independently selectable.
Input Connections (Stereo Modules): 2 Unbalanced (RCA); 2 balanced (XLR); two per channel, independently selectable.
Speaker Output Connections: Audiophile grade, gold plated, 5-way binding posts.

TRIGGER & POWER REQUIREMENTS

Trigger Input: 5 – 12 V (AC or DC); <10 mA input current required.
Trigger Output: 12 VDC; can drive any load up to 120 mA.
Power Requirements: Between 100 VAC and 250 VAC @ 50 / 60 Hz (automatically detected).

CONTROLS & INDICATORS

Standby: push button (halo ring changes color to indicate Standby or On)
Status LEDs: one per channel; blue Status LEDs change to red to indicate a fault condition.
AC Power switch: rocker switch (switches AC main power)
Status LEDs switch: disables front panel Status LEDs and dims Standby button halo.
Input selector switches (one per channel): metal toggle switches; select between balanced and unbalanced inputs.
Circuit Breaker: press button to reset circuit breaker

PROTECTION & MECHANICAL

Protection: The XPA Gen3 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions.
Dimensions: 17” wide x 8” high x 19” deep (unboxed; including feet) 17” wide x 7” high x 19” deep (unboxed; without feet) 24-1/2” wide x 12” high x 24-3/4” deep (boxed)
Weight: 35.5 lbs (unboxed) 40.5 lbs (boxed)